Gas detection

Made in sweden

Shelf life 5 years

XgardIQ transmitter, ATEX/IECEx certified, 4-20mA output, three M20 cable entries, 316 stainless steel, hydrogen sensor module (0-100% LEL) PN: XIQ-AF-S1-011-Z-Z-A

Adding Relay module to XgardIQ provides Alarm 1, Alarm 2 and Fault SPCO contacts rated 230Vac 5A. Adding R to PN: XIQ-XX-XX-XXX-X-R-X.

Adding HART communications over the 4-20mA signal and via local I.S. pins for HART communicator connection.. Adding H to PN: XIQ-XX-XX-XXX-H-X-X.

"Duct mounting kit - for ducts between 300mm and 3m wide, air-flows from 4 to 20m/s. Note: this accessory can only be used in conjunction with the remote sensor assembly." PN:C01894

XgardIQ remote sensor assembly. 5 meter cable . PN:S012325

XgardIQ remote sensor assembly. 15 metre cable .PN:S012331

Smart 3G-C2 Atex Zone 1 Toxic Electrochemical Sensors and Oxygen • Standard 4-20 mA 3 wire output • Optional 1 or 3 relay output • Optional RS485 interface for Modbus communication. • Zero tracking to maintain the zero point steady from possible drifts • Ongoing system self diagnosis • ATEX II 2G Ex db IIC T5 Gb (standard marking) (II 2GD with optional adapter) • ATEX II 2G Ex db [ib] ib IIC T6 Gb for detectors with intrinsically safe protection • SIL 2 HW & SIL3 SW certified

SMART3G-D2 feature:  Non-intrusive one man calibration via Hall effect switches  4-digit display and 5 mode status LEDs  Multi-color LED light ring  Standard 4-20 mA 3 wire output  Standard 3 relay output  Optional RS485 interface for Modbus communication.  Zero tracking to maintain the zero point steady from possible drifts  Ongoing system self diagnosis  ATEX II 2G Ex db IIC T5 Gb (standard marking) (II2 GD with optional adapter)  ATEX II 2G Ex db [ib] IIC T6 Gb for detectors with intrinsically safe protection  SIL 2HW & SIL3 SW certified  Wide range of sensors and detectable gases  Wide range of accessories for installation and maintenance  Easy sensor replacement

SF6 & Refrigeratent Infra-Red (IR) Sensors• Non-intrusive one man calibration via Hall effect switches • 4-digit display and 5 mode status LEDs • Multi-color LED light ring • Standard 4-20 mA 3 wire output • Standard 3 relay output • Optional RS485 interface for Modbus communication. • Zero tracking to maintain the zero point steady from possible drifts • Ongoing system self diagnosis ATEX II 2G Ex db IIC T5 Gb (standard marking) • ATEX II 2GD Ex db IIC T5 Gb (II2 GD with optional adapter to be specified at the order) • ATEX II 2G Ex db [ib] ib IIC T6 Gb for detectors with intrinsically safe protection • SIL 2HW & SIL3 SW certified

Smart 3G-C2 Atex Zone 1 Flammable Catalytic Sensors • Standard 4-20 mA 3 wire output • Optional 1 or 3 relay output • Optional RS485 interface for Modbus communication. • Zero tracking to maintain the zero point steady from possible drifts • Ongoing system self diagnosis • ATEX II 2G Ex db IIC T5 Gb (standard marking) (II 2GD with optional adapter) • ATEX II 2G Ex db [ib] ib IIC T6 Gb for detectors with intrinsically safe protection • SIL 2 HW & SIL3 SW certified

CO detector series SMART P for car parks sensing element: Electrochemical cell Range: 0-300 ppm Output: serial RS485 to communicate with MULTISCAN++PK control panels Power Supply: 12-24Vdc Compiance with EN 50545-1

XgardIQ transmitter, ATEX/IECEx certified, 4-20mA output, three M20 cable entries, 316 stainless steel, hydrogen sensor module (0-100% LEL) PN: XIQ-AF-S1-011-Z-Z-A

Adding Relay module to XgardIQ provides Alarm 1, Alarm 2 and Fault SPCO contacts rated 230Vac 5A. Adding R to PN: XIQ-XX-XX-XXX-X-R-X.

Adding HART communications over the 4-20mA signal and via local I.S. pins for HART communicator connection.. Adding H to PN: XIQ-XX-XX-XXX-H-X-X.

"Duct mounting kit - for ducts between 300mm and 3m wide, air-flows from 4 to 20m/s. Note: this accessory can only be used in conjunction with the remote sensor assembly." PN:C01894

XgardIQ remote sensor assembly. 5 meter cable . PN:S012325

XgardIQ remote sensor assembly. 15 metre cable .PN:S012331

SMART3G-C2-LD feature:  Standard 4-20 mA 3 wire output  Standard 3 relay output  Standard multi-color LED light ring  Optional RS485 interface for Modbus communication.  Zero tracking to maintain the zero point steady from possible drifts  Ongoing system self diagnosis  ATEX II 2G Ex db IIC T5 Gb (standard marking) (II2 GD with optional adapter)  ATEX II 2G Ex db [ib] IIC T6 Gb for detectors with intrinsically safe protection  SIL 2HW & SIL3 SW certified  Wide range of sensors and detectable gases  Wide range of accessories for installation and maintenance  Easy sensor replacement

SMART3G-C2 feature:  Standard 4-20 mA 3 wire output  Optional 1 or 3 relay output  Optional RS485 interface for Modbus communication.  Zero tracking to maintain the zero point steady from possible drifts  Ongoing system self diagnosis  ATEX II 2G Ex db IIC T5 Gb (standard marking) (II 2GD with optional adapter) ATEX II 2G Ex db [ib] IIC T6 Gb for detectors with intrinsically safe protection  SIL 2 HW & SIL3 SW certified  Wide range of sensors and detectable gases  Wide range of accessories for installation and maintenance  Easy sensor replacement

SMART3G-C2 feature:  Standard 4-20 mA 3 wire output  Optional 1 or 3 relay output  Optional RS485 interface for Modbus communication.  Zero tracking to maintain the zero point steady from possible drifts  Ongoing system self diagnosis  ATEX II 2G Ex db IIC T5 Gb (standard marking) (II 2GD with optional adapter) ATEX II 2G Ex db [ib] IIC T6 Gb for detectors with intrinsically safe protection  SIL 2 HW & SIL3 SW certified

SMART3G-C2 feature:  Standard 4-20 mA 3 wire output  Optional 1 or 3 relay output  Optional RS485 interface for Modbus communication.  Zero tracking to maintain the zero point steady from possible drifts  Ongoing system self diagnosis  ATEX II 2G Ex db IIC T5 Gb (standard marking) (II 2GD with optional adapter) ATEX II 2G Ex db [ib] IIC T6 Gb for detectors with intrinsically safe protection  SIL 2 HW & SIL3 SW certified  Wide range of sensors and detectable gases  Wide range of accessories for installation and maintenance  Easy sensor replacement

SMART3G-C2 feature:  Standard 4-20 mA 3 wire output  Optional 1 or 3 relay output  Optional RS485 interface for Modbus communication.  Zero tracking to maintain the zero point steady from possible drifts  Ongoing system self diagnosis  ATEX II 2G Ex db IIC T5 Gb (standard marking) (II 2GD with optional adapter) ATEX II 2G Ex db [ib] IIC T6 Gb for detectors with intrinsically safe protection  SIL 2 HW & SIL3 SW certified  Wide range of sensors and detectable gases  Wide range of accessories for installation and maintenance  Easy sensor replacement

BeSafe Battery storage Gas detector 0-100%LEL H2 , Co 100 PPM STD

SF6 & Refrigeratent Infra-Red (IR) Sensors• Non-intrusive one man calibration via Hall effect switches • 4-digit display and 5 mode status LEDs • Multi-color LED light ring • Standard 4-20 mA 3 wire output • Standard 3 relay output • Optional RS485 interface for Modbus communication. • Zero tracking to maintain the zero point steady from possible drifts • Ongoing system self diagnosis ATEX II 2G Ex db IIC T5 Gb (standard marking) • ATEX II 2GD Ex db IIC T5 Gb (II2 GD with optional adapter to be specified at the order) • ATEX II 2G Ex db [ib] ib IIC T6 Gb for detectors with intrinsically safe protection • SIL 2HW & SIL3 SW certified

Sensit SMART-CAL 360 Desktop (With Pump)

SMART 3 NC Gas detector for safe areas For Car Park Applications • Standard 4-20 mA 3 wire output • Optional 3 relay output • Optional RS-485 interface for Modbus communication. • Ongoing system self diagnosis

Constituents.. 1) [S2097ME]Smart 3G-C2, Methane Cat 0-100% LEL - 1 Each 2) [STS1REL]1-Relay card for SMART3G. Relay at 12÷24V - 1 Each

Constituents.. 1) [S2097ME]Smart 3G-C2, Methane Cat 0-100% LEL - 1 Each 2) [STS3REL]3-Relay card for SMART3G. Relay at 12÷24V - 1 Each

Constituents.. 1) [S2097H2]Smart 3G-C2, Hydrogen Cat 0-100% LEL - 1 Each 2) [STS3REL]3-Relay card for SMART3G. Relay at 12÷24V - 1 Each

Constituents.. 1) [S2097H2]Smart 3G-C2, Hydrogen Cat 0-100% LEL - 1 Each 2) [STS1REL]1-Relay card for SMART3G. Relay at 12÷24V - 1 Each

The SMART 3G-C2-LD is designed to meet the demands of industrial applications, providing reliable monitoring of toxic, flammable, and refrigerant gases in classified areas. Its multi-color LED light ring offers immediate visual indication of the detector's status. Ideal for industrial environments, the SMART 3G-C2-LD features one-man calibration using the STS/CKD+ calibration keypad. These detectors can accurately monitor flammable compounds (% LFL), toxic compounds and refrigerant gases in ppm, as well as oxygen and CO2 levels (% by volume). The detectors are rated IP65 for protection against dust and water. Features: • Standard 4-20 mA 3 wire output • Standard 3 relay output • Standard multi-color LED light ring • Optional RS485 interface for Modbus communication. • Zero tracking to maintain the zero point steady from possible drifts • Ongoing system self diagnosis • ATEX II 2G Ex db IIC T5 Gb (standard marking) • ATEX II 2GD Ex db IIC T5 Gb (with optional adapter to be specified at the order) • ATEX II 2G Ex db [ib] ib IIC T6 Gb for detectors with intrinsically safe protection • SIL 2HW & SIL3 SW certified

The SMART 3G-C3 gas detectors are designed to meet industrial requirements, enabling the monitoring of toxic, flammable, and refrigerant gases in areas classified as Zone 2, Category 3. Ideal for light industrial environments, the SMART 3G-C3 features one-man calibration using the STS/CKD+ calibration keypad. These detectors can reliably monitor flammable compounds (% LFL), toxic and refrigerant gases in ppm, as well as oxygen and CO2 levels (% by volume). Features: • Standard 4-20 mA 3 wire output • Optional 1 or 3 relay output • Optional RS485 interface for Modbus communication. • Ongoing system self diagnosis • ATEX: II 3G Ex db ec nC IIC T5 Gc • SIL 2 HW & SIL3 SW certified • IP55

The SMART 3G-D2 is designed to meet rigorous industrial standards, enabling the monitoring of toxic, flammable, and refrigerant gases in harsh environments and classified areas. It features a 4-digit back-lit display for gas concentration readings, five mode status LEDs, and a high-visibility multi-color LED light ring. Ideal for use in challenging environments, the SMART 3G-D2 offers non-intrusive calibration for precise and easy adjustments via Hall-effect switches, eliminating the need to open the instrument and declassify the area. It can reliably monitor flammable compounds (% LFL), toxic compounds (ppm), oxygen and CO2 levels (% by volume), and refrigerant gases in both ppm and % LFL. Features: • Non-intrusive one man calibration via Hall effect switches • 4-digit display and 5 mode status LEDs • Multi-color LED light ring • Standard 4-20 mA 3 wire output • Standard 3 relay output • Optional RS485 interface for Modbus communication. • Zero tracking to maintain the zero point steady from possible drifts • Ongoing system self diagnosis ATEX II 2G Ex db IIC T5 Gb (standard marking) • ATEX II 2GD Ex db IIC T5 Gb (II2 GD with optional adapter to be specified at the order) • ATEX II 2G Ex db [ib] ib IIC T6 Gb for detectors with intrinsically safe protection • SIL 2HW & SIL3 SW certified • IP rating IP65

The SMART 3G-C2 is designed to meet industrial requirements, enabling the monitoring of toxic, flammable, and refrigerant gases in industrial environments and classified areas. Ideal for industrial settings, the SMART 3G-C2 features one-man calibration using the STS/CKD+ calibration keypad. These detectors can reliably monitor flammable compounds (% LFL), toxic compounds and refrigerant gases in ppm, as well as oxygen and CO2 levels (% by volume). The detectors are rated IP65 for protection against dust and water. Features: • Standard 4-20 mA 3 wire output • Optional 1 or 3 relay output • Optional RS485 interface for Modbus communication. • Zero tracking to maintain the zero point steady from possible drifts • Ongoing system self diagnosis • ATEX II 2G Ex db IIC T5 Gb (standard marking) (II 2GD with optional adapter) • ATEX II 2G Ex db [ib] ib IIC T6 Gb for detectors with intrinsically safe protection • SIL 2 HW & SIL3 SW certified

The SMART 3G-D3 is designed to meet industrial requirements, enabling the monitoring of toxic and flammable gases in Zone 2 classified areas. It features a 4-digit back-lit display for gas concentration readings, five mode status LEDs, and a high-visibility multi-color LED light ring. The SMART 3G-D3 offers non-intrusive calibration for accurate and easy adjustments via Hall-effect switches, without the need to open the instrument and declassify the area. These detectors can reliably monitor flammable compounds (% LFL), toxic compounds in ppm, as well as oxygen and CO2 levels (% by volume). Features: • Non-intrusive one man calibration via Hall effect switches • 4-digit display and 5 mode status LEDs • Multi-color LED light ring • Standard 4-20 mA 3 wire output • Standard 3 relay output • Optional RS485 interface for Modbus communication. • Zero tracking to maintain the zero point steady from possible drifts • Ongoing system self diagnosis • ATEX: II 3G Ex db ec nC IIC T5 Gc • SIL 2 HW & SIL3 SW certified • IP55

The SMART 3-NC detectors are designed to offer cost-effective solutions with high-tech professional features for car parks and non-classified areas.

XGARD H2S SENSOR ASSY 0- 50PPM SPARE sensor

Crowcon Flame guard plus Spare sensor 96HD/FL HEAD (POISON RES) VQ21TB PELL-SPARE-FGS

SMART 3G-GR1 Gas Detectors for Group I Mines and Tunnels With Display Features: • Stainless steel enclosure • Non-intrusive one man calibration via Hall effect switches (display version) • 4-digit display and multi-color LED light ring (display version) • Standard 4-20 mA 3 wire output • Optional 3 relay output (standard 3-relay output in display version) • Optional RS485 interface for Modbus communication. • Zero tracking to maintain the zero point steady from possible drifts • Ongoing system self diagnosis • ATEX I M2 Ex d I Mb • SIL 2HW & SIL3 SW certified

SMART 3G-GR1 Gas Detectors for Group I Mines and Tunnels With Display Features: • Stainless steel enclosure • Non-intrusive one man calibration via Hall effect switches (display version) • 4-digit display and multi-color LED light ring (display version) • Standard 4-20 mA 3 wire output • Optional 3 relay output (standard 3-relay output in display version) • Optional RS485 interface for Modbus communication. • Zero tracking to maintain the zero point steady from possible drifts • Ongoing system self diagnosis • ATEX I M2 Ex d I Mb • SIL 2HW & SIL3 SW certified

SMART 3G-GR1 Gas Detectors for Group I Mines and Tunnels With Display Features: • Stainless steel enclosure • Non-intrusive one man calibration via Hall effect switches (display version) • 4-digit display and multi-color LED light ring (display version) • Standard 4-20 mA 3 wire output • Optional 3 relay output (standard 3-relay output in display version) • Optional RS485 interface for Modbus communication. • Zero tracking to maintain the zero point steady from possible drifts • Ongoing system self diagnosis • ATEX I M2 Ex d I Mb • SIL 2HW & SIL3 SW certified